Irving Pool Builders provides professional spa & hot tub installation in Irving, TX for residential and commercial properties across the Las Colinas and mid-cities area. A spa is the part of the build you'll actually use in December.
Irving gets roughly four months where the pool is genuinely inviting on its own, and a heated spa turns a good chunk of the other eight into a reason to walk outside on a Wednesday night in a dressing gown.
On a new build we design the spa into the shell from the start, which is always cheaper and always looks better than bolting one on later. Shared plumbing and a shared pad.
A raised wall with a spillover into the pool, set high enough that you hear it from the patio without shouting over it.
Bench and jet layout drawn around the people who will actually sit in it, because a therapy seat that fits a six-foot adult doesn't fit a ten-year-old and the pair of them will fight about it forever.
Seats run 18 to 20 inches deep, jets get aimed at shoulders and lumbar rather than sprayed evenly like a car wash, and the spa gets its own pump. Throttling the pool pump down to run a dozen jets gives you a bath with ambition.
A 400,000 BTU heater takes a 600-gallon spa from cold to 102 in around 25 minutes, and paired with a Pentair, Hayward or Jandy controller you can start that from your phone before you leave the office on State Highway 114.
That combination is the whole argument for automation in one sentence. On an existing pool we tie new steel into the old bond beam, gunite the spa as a raised structure, re-plumb the pad and add the actuated valves that let one system be two.
Figure a three to four week add. Standalone acrylic hot tubs are the quick answer where there's no pool: a level pad rated for the filled weight, a dedicated 50-amp GFCI circuit, and a route into the yard wide enough to get it there.
That last one catches people out in Valley Ranch and Hackberry Creek, where the side gate is often narrower than the tub, and the answer becomes a crane over the roof.
We measure before you buy, not after it's sitting on your driveway under a tarp. Maintenance reality: a spa runs hot, so calcium drops out of our hard water faster than it does in the pool.
Expect to clean the spa waterline more often, and keep an eye on the heat exchanger. Honest advice on whether to build one at all. If you're pretty sure you'll use it three times a year, don't pour a gunite spa.
A plug-in acrylic tub costs a fraction, needs no shell work, and you can take it with you when you move.
Build the gunite spa when you want it to be part of the pool, visually and structurally, and when you know you're the sort of household that will sit in it in February.
With 15+ years of experience, our insured team brings the right materials and equipment to every job — gunite and shotcrete shells, one-piece fiberglass pool shells, PebbleTec and polished quartz interiors, glass mosaic and large-format porcelain tile, travertine coping and decking, variable-speed pumps — and backs the work with a written workmanship warranty. We serve Irving and nearby communities including Coppell, Grapevine, Southlake, Colleyville.
What We Handle
Everything our spa & hot tub installation in Irving covers
One crew, one point of contact, and the full range of spa & hot tub installation work in Irving, TX. If it is on this list we do it in house rather than handing it to a subcontractor:
- attached gunite spa construction
- spa spillover and raised spa wall
- adding a spa to an existing pool
- standalone hot tub installation
- therapy jets, blowers and seating layout
- dedicated spa heater and pump
- spa resurfacing, tile and reseal
- swim spa installation
- spa automation and remote heating
- spa pad, wiring and access planning
Not sure which one describes your situation? Describe it in plain words and we will sort it out — or browse the rest of our Irving services.
Materials, equipment and how we do spa & hot tub installation
The difference between spa & hot tub installation that lasts and spa & hot tub installation that gets redone in three years is almost always preparation and materials, not the finish you see on day one. We work with gunite and shotcrete shells, one-piece fiberglass pool shells, PebbleTec and polished quartz interiors, glass mosaic and large-format porcelain tile, spec them to the job instead of to the invoice, and write the material grades into the free estimate so you know exactly what you are buying.
Every Irving job runs the same way: site walk and measurements, written scope and fixed price, protection of the surrounding area, then the work itself with a daily clean-up. 15+ years of pool work in the Las Colinas and mid-cities area means we have already met whatever your property is going to throw at us — awkward access, older construction, an HOA with opinions.
Where we do spa & hot tub installation outside Irving
Irving Pool Builders covers Irving and the surrounding communities of the Las Colinas and mid-cities area. Crews run out to the same nearby cities every week, so an out-of-town job does not mean an out-of-town price.
- Spa & Hot Tub Installation in Coppell, TX — Dallas County, population 43,000
- Spa & Hot Tub Installation in Grapevine, TX — Tarrant County, population 51,000
- Spa & Hot Tub Installation in Southlake, TX — Tarrant County, population 31,000
- Spa & Hot Tub Installation in Colleyville, TX — Tarrant County, population 26,000
- Spa & Hot Tub Installation in Flower Mound, TX — Denton County, population 76,000
- Spa & Hot Tub Installation in Lewisville, TX — Denton County, population 112,000
Start on the Irving Pool Builders homepage for a free estimate, or call (877) 730-2126 and describe the job.
Why Irving Chooses Irving Pool Builders
- ✓Over 15 years building and servicing pools across Irving, Las Colinas and the mid-cities
- ✓Gunite, shotcrete and fiberglass construction, plus full remodels on pools we did not build
- ✓Experienced with tight zero-lot-line access, conveyor spoil removal and long gunite hose runs
- ✓HOA architectural review packets prepared as part of the job, not billed as an extra
The standards behind spa & hot tub installation
Quality here is not a matter of opinion — it is written down. The spa & hot tub installation work we do in Irving follows published industry standards: Pool & Hot Tub Alliance publishes the ANSI/APSP construction and barrier standards, and American Red Cross water safety sets out the layered-protection guidance every pool owner should read. If a contractor cannot tell you which standard a detail comes from, that is worth asking about before you sign.
Every spa & hot tub installation project in Irving gets the same attention, whether it is a single room or a full commercial job. We show up on schedule, keep the site clean, and stand behind the work — the estimate is free and there is no pressure.
Ready to get started? Call (877) 730-2126 for a free spa & hot tub installation free estimate in Irving, or request a quote and we'll get right back to you.